A door sitting at an angle usually means a cable has slipped or a roller has left the track. We relieve the tension carefully, reseat the door, replace whatever let go, and look over the tracks for the bend that caused it.
Same fees day or night · Toronto
Pick the closest, or call (365) 605-5927
Repair & MaintenanceInspection, adjustment, sealing, and section-level repairs.
Springs & HardwareCounterbalance, track, roller, cable, and hinge work.
Openers & AccessOperators, safety sensors, controls, and access systems.
Installation & UpgradesResidential and commercial replacement, upgrades, sectional-door, and rolling-door work.Springs and cables are under a great deal of tension, and the proper way to handle them is well understood: the right winding bars, the door clamped, the tension released in steps. That care is simply how the job is done. It is also why our repairs hold and why the door runs true afterwards.
Nearby Bedford Park, Davisville, Lawrence Park and North Toronto
Keeping the weather on the outside.
31 years in business · Tell us what happened: (365) 605-5927
Garage door spring replacement
Garage doors rarely fail all at once. They give hints first, and this list is arranged around those hints. Match the one you have noticed and you will see what the visit involves and which parts are usually behind it.
This is the heavy side of garage door work.
This is where a door comes when it is still worth keeping.
A garage door belongs to the architecture. Its movement belongs to your everyday life. We bring both into the conversation.
Job sheet1 of 3
ServiceTorsion Spring Replacement
Job sheet2 of 3
Job sheet3 of 3
This is the heavy side of garage door work. A technician with winding bars, a set of stands and a measured approach can make a door that was dangerous to move feel light again.
Part 1The panels
After an overnight freeze the door stuck to the slab, the opener strained, and something gave. The bottom section is bowed inward, one hinge has torn free of its screws, and the rubber seal along the bottom no longer sits flat.
Part 2The springs
The door starts to rise, gets about the height of your knee, then shudders and reverses. The opener sounds strained, and the top section flexes as the trolley pulls on it, because the motor is doing work the spring used to do.
Part 3The cables
The car bumper kissed the door on the way in. The bottom panel has a dent, the bracket in that corner sits crooked, and the cable on that side has jumped and gone slack, so the door reverses every time it tries to close.
Part 4Tracks and rollers
A roller near the top corner is riding on the lip of the track rather than inside it, and the section above leans back a little more each week. The door still moves, but it looks one bump away from coming out altogether.
Part 5The opener
It is a January morning and the door lifts about a hand's width, groans, and settles back down. When you pull the release and try by hand the door feels far heavier than it used to, and the bottom seal is stuck hard to the slab.
Garage Door Safety Inspection. There is a new sound.
Request a visit
Commercial doorsWhen
Openers
Keyless entry, phone control, vehicle integration and a plain reliable remote: however you prefer to open the door, we set it up and show you how to add or remove devices yourself when you need to.
Door samples
Insulation is described in different ways by different makers, and the numbers are easy to misread. We explain what a given door construction actually does for your garage in plain language before you commit to one.
Tap a situation. The answer opens here.
If The door will not lift and you heard a loud bang from the garage.
Then Torsion spring replacement.
A snapped spring leaves a visible gap in the coil; the opener should stay off until it is replaced. Torsion Spring Replacement
If The door rises a few centimetres, stops and settles back down.
Then Spring and opener force check.
Often the spring has lost tension and the opener is protecting itself; balancing the door usually resolves it. Torsion Spring Replacement
If The opener runs and the chain moves but the door stays put.
Then Trolley and drive gear repair.
The trolley may be disconnected or the drive gear worn; both are common, repairable faults.
Five scenes · open 24/7
Springs and cables are under a great deal of tension, and the proper way to handle them is well understood: the right winding bars, the door clamped, the tension released in steps. That care is simply how the job is done.
Step 1 of 5
Describe the property, the hardware and what has changed, and the visit starts from what you have seen.
Step 2 of 5
The door is heavy, the opener hums, the remote is dead. Whatever it is, say it in your own words and we translate it into a plan.
Step 3 of 5
You will know what is worn, why it failed and what the options are before a single bolt is turned. Questions are welcome at every step.
Step 4 of 5
Drop cloths where needed, old parts bagged, floor swept. We leave the space as we found it, only with a working door.
Step 5 of 5
If a repair will do, we say so. If a replacement makes more sense, we explain why and let you decide.
TorontoOntario
Every square is one home in a hundred.
Hinges and rollers that are bent, cracked or worn are replaced with the section, and the technician checks each one on the affected joints. Sound hinges can be transferred, always by their stamped number, since each position in the door uses a different offset. Rollers that have flat spots, wobbly stems or dried bearings are swapped, often for nylon rollers that run quietly. Fasteners are always new, driven into fresh holes in the new stiles.
It is disconnected at the release cord and unplugged before any hardware comes off, so the motor cannot pull on a door that is missing a section. After the new section is in and the door has been balanced by hand, the opener is reconnected and tested: its reversal against a board on the floor and its photo-eyes are checked every time, and the open and close limits or the force setting are reset only if that check shows they need it.
Enough to bring the new section in, lay it flat, and work at both tracks and the spring shaft. Moving vehicles out of the garage and clearing a metre or two along the walls where the tracks run makes the job smoother, as does clear access to the opener and the ceiling around the spring. Sections are handled by two people and are wider than the door opening, so a clear path from the driveway helps.
A spring that is intact but has relaxed slightly can be given a little more tension, within limits, to restore balance; this is a normal adjustment on a door that has settled. A spring with a broken coil is replaced as a unit, since the wire has reached the end of its life. The technician checks the condition of the steel and recommends whichever restores a balanced, safe door.
On-site assessment preferred · (365) 605-5927, open 24/7